Our Service

Logo 2020

ESD TRAINING GALLERY: 

           Initial and recurrent ESD awareness and prevention training shall be provided to all personnel who handle or otherwise come into contact with any ESDS items. Initial training shall be provided before personnel handle ESDS items.
           The type and frequency of ESD training for personnel shall be defined in the Training Plan. The Training Plan shall include a requirement for maintaining employee training records and shall document where the records are stored. Training methods and the use of specific techniques are at the Or ganization’s discretion. The training plan shall include the methods used by the rganization to verify trainee comprehension and training adequacy.

 

 
ESD Association Standard/ANSI/ESD S20.20-2014
ESD Association Standard for the Developmen t of an Electrostatic Discharge Control Program for Protection of Electrical and Electronic Parts, Assemblies and Equipment(Excluding Electrically Initiated Explosive Devices)
7.0 ESD CONTROL PROGRAM ADMINISTRATIVE REQUIREMENTS
  • 7.1 ESD Control Program Plan The Organization shall prepare an ESD Control Program Plan that addresses each of the requirements of the Program. Those requirements include: - Training  - Product Qualification (New) - Compliance Verification - Grounding / Equipotential Bonding Systems - Personnel Grounding - ESD Protected Area (EPA) Requirements - Packaging Systems - Marking
           The ESD Control Program Plan is the principal document for implementing and verifying the Program. The goal is a fully implemented and integrated Program that conforms to internal quality system requirements. The ESD Control Program Plan shall apply to all applicable facets of the Organization’s work.
7.2 Training Plan Initial and recurrent ESD awareness and prevention training shall be provided to all personnel who handle or otherwise come into contact with any ESD sensitive (ESDS) items. Initial training shall be provided before personnel handle ESDS items. The type and frequency of ESD training for personnel shall be defined in the Training Plan. The Training Plan shall include a requirement for maintaining employee training records and shall document where the records are stored. Training methods and the use of specific techniques are at the Organization’s discretion. The training plan shall include the methods used by the Organization to verify trainee comprehension and training adequacy.
7.3 Product Qualification Plan A Product Qualification Plan shall be established to ensure that the ESD control items that have been selected meet the requirements in the plan. The test methods and required limits are located in the product qualification columns in Tables 2 and 3. Product qualification is normally conducted during the initial selection of ESD control items. Any of the following methods can be used: product specification review, independent laboratory evaluation or internal laboratory evaluation. For ESD control items that were installed by the Organization before the adoption of this standard, on-going compliance verification records can be used as evidence of product qualification.
7.4 Compliance Verification Plan A Compliance Verification Plan shall be established to ensure the Organization’s fulfillment of the technical requirements of the ESD Control Program Plan. Measurements shall be conducted in accordance with a Compliance Verification Plan that identifies the technical requirements to be verified, the measurement limits and the frequency at which those verifications occur. The Compliance Verification Plan shall document the test methods and equipment used for making the measurements. If the test methods used by the Organization differ from any of the standards referenced in this document, then there must be a tailoring statement that is documented as part of the ESD Control Program Plan. Compliance verification records shall be established and maintained to provide evidence of conformity to the technical requirements. The test equipment selected shall be capable of making the measurements defined in the Compliance Verification Plan.
8.0 ESD CONTROL PROGRAM PLAN TECHNICAL REQUIREMENTS Sections 8.1 to 8.5 describe the key technical requirements used in the development of an ESD Control Program. The required limits are based on the test methods or standards listed in each table. The Compliance Verification Plan shall document the methods used to verify the limits.

If you need product qualification report for your product, please be contact to us

If you are finding who is can do your product qualification please be contact to us

Product Qualification: Product qualification is normally conducted during the initial selection of ESD control items

A Product Qualification Plan shall be established to ensure that the ESD control items that have been selected meet the requirements in the plan. The test methods and required limits are located in the product qualification columns in Tables 2 and 3. Product qualification is normally conducted during the initial selection of ESD control items. Any of the following methods can be used: product specification review, independent laboratory evaluation or internal laboratory evaluation. For ESD control items that were installed by the Organization before the adoption of this standard ,on-going compliance verification records can be used as evidence of product qualification.
สำหรับตัวแทนจำหน่าย ผลิตภัณฑ์ป้องกันไฟฟ้าสถิต อาทิเช่น
  – ESD Glove
  – ESD MAT (Worksurface, Green MAT)
  – Wrist Strap
  – Personal Ground Wrist Strap
  – Footwear
  – Seating
  – Flooring
  – Shelving (When using at Store)
  – Ionization
  – Garment
 หากท่านกำลัง เจอปัญหาสินค้าไม่มีใบ Certificate
เรารับตรวจสอบ Product ข้างต้นนี้ หากท่านจำหน่ายอยู่นั้น ติดปัญหาการทำ Product Qualification ให้ลูกค้าได้ และ ไม่มีใบ Certificate รับรองคุณภาพ หรือลูกค้าไม่กล้าตัดสินใจซื้อ เกิดคำถาม
 1. คุณภาพดีและปลอดภัยกับอุปกรณ์ ESD Sensitive Device หรือไม่
 2. Product ของคุณมีใบรับรองหรือไม่ Certificate
 3. จะผ่านการทดสอบ Product Qualification หรือไม่
 4. ค่า Surface resistance เท่าไร
 5. ค่า Point to Point เท่าไร
เราสามารถช่วยท่านได้ เรามีความรู้ความเชี่ยวชาญ เพื่อเสริมและทดสอบผลตาม STD s.20-20 เพิ่มความมั่นใจในตัว Product ให้ท่านได้ และ เพิ่มความมั่นใจให้เกิดกับลูกค้าของท่าน เพิ่มยอดขาย และ สุดท้ายท่านจะได้ความน่าเชื่อถือ เกิดความมั่นใจให้กับลูกค้าของท่านอย่างยอดเยี่ยม
แนะนำถุงที่เราได้ตรวจสอบ
ถุงมือ ozu

Detail

Surface Resistance (More Detail please refer to ESD Tips) The Surface Resistance Meter Kit (or its Meter) is referenced and designed to be used to make measurements in accordance with the test procedures in:
  • Compliance Verification – ESD TR53 – Resistance Measurements
  • Worksurfaces – ANSI/ESD S4.1 Worksurfaces
  • Floors – ANSI/ESD S7.1- Resistive Characterization of Materials Floor Materials
  • Foot Grounders – ESD SP9.2 – Foot Grounders Resistive Characterization
  • Garments – ANSI/ESD STM2.1 Garments
  • Seating – ANSI/ESD STM12.1- Seating – Resistive Measurement
  • Floor/Footwear – ANSI/ESD STM97.1 – Floor Materials and Footwear- Resistance Measurement in Combination with a Person
“A Compliance Verification Plan shall be established to ensure the Organization’s fulfillment of the technical requirements of the ESD Control Program Plan. Process monitoring (measurements) shall be conducted in accordance with a Compliance Verification Plan that identifies the technical requirements to be verified, the measurement limits and the frequency at which those verifications shall occur. The Compliance Verification Plan shall document the test methods and equipment used for process monitoring and measurements. If the test methods used by the Organization differ from any of the standards referenced in this document, then there must be a tailoring statement that is documented as part of the ESD Control Program Plan. Compliance verification records shall be established and maintained to provide evidence of conformity to the technical requirements. The test equipment selected shall be capable of making the measurements defined in the Compliance Verification Plan.” (ANSI/ESD S20.20 section 7.3) Reference Literature In addition to those noted above: ANSI/ESD S20.20 – Development of ESD Control Program ESD ADV1.0 – Glossary of Terms ANSI/ESD S6.1 Grounding Field Meter (More Detail please refer to ESD Tips) Charger (More Detail please refer to ESD Tips) EM eye (More Detail please refer to ESD Tips) ESD event measurement- offers same performance as the 3M™ EM Aware ESD Monitor And the 3M™ ESD Pro ESD Event Indicator
  1. Highly sensitive ESD event measurements
  2. CDM mode-rejection of non-ESD EMI events
     iii. Full characterization for ESD event strength
  1. Threshold setting
  2. Data logging
The base unit is never obsolete as each sensor carries its own software. Target Market Segments
  • Printed circuit board manufacturing (contract manufacturers)
  • Hard disk drive manufacturers of final drive assembly, heads and disk media
  • Defense/aerospace
  • Medical equipment manufacturing
  • Companies that install and manage mobile phone towers
  • Design and maintenance engineers interested in RF measurements
  • Semi-conductor
Ground Pro (More Detail please refer to ESD Tips) ESD Tester (Check Wrist Strap and ESD Shoes)

13,698 total views, 6 views today

Post Views: 0